12.6V5A氮化镓方案锂电池充电器 65W锂电池充电器

1 产品名称：12.6V 5A锂电充电器
2 产品型号：GBT-1265000-GaN / TP06-126500W

3ELECTRICAL CHARACTERISTICS电气性能

3.1ACInputVoltageandFrequency输入电压及频率

2.1.1 ReliableInput Voltage可输入电压范围: AC200-264V

2.1.2 RatedInput Voltage额定输入电压: AC200-240V

2.1.3 ReliableInputFrequency可输入频率范围: 47-63Hz

2.1.4 RatedInputFrequency额定输入频率: 50/60Hz

3.2Maximum AC Current最大输入电流

Inputrated voltage,Ouputratedload.Input AC Current 5.0AmpsMaximum.

输入额定电压,输出额定负载条件下,最大输入电流为:5.0Amps。

Inputrated voltage,Ouputnoload.Input AC Current 0.05AmpsMaximum.

输入额定电压,输出空载条件下,最大输入电流为:0.05Amps。

3.3InputInrush Current最大浪涌(突入)电流

Input110&230Vac 50/60Hz,Ouputratedload.Maximum cold startinrush Current 80Ampspeak.输入110&230Vac50/60Hz,输出额定负载(冷启动)条件下,最大浪涌(突入)电流为:80Amps。

3.4No-loadLossPower空载功耗

InputRated Voltage,Outputno load.Maximumlosspower 0.21WattsMAX.

输入额定电压,输出额定负载,最大空载功耗为:0.21瓦最大。

3.5 Output Voltage输出电压

Parameter	MIN	Type	MAX	Units	Notes
OutputVoltage输出电压	5.5	12	12.6	V	CV=5.5- 12.6V CC=4.9-5.1A
OutputCurrent输出电流	5	5	0	A

3.6 OutputRipple Voltage输出纹波电压

3.6.1 Outputripple test condition:inputrated voltage and ouputratedload.

在额定输入及输出的条件下测试输出纹波电压。

3.6.2Peak topeakrippleismeasured with anoscilloscope with abandwidth of 20MHz.纹波量测时示波器选用20MHz带宽限制。

3.6.3Measurement of ripple shouldinclude a 0.1uFceramiccapacitor anda47uFelectrolytic capacitor at theinputof the measuringoscilloscope.

测试时在输出端要并联一颗0.1uF的陶瓷电容和一颗47uF的电解电容。

Input	OutputRated Voltage	OutputCurrent	OutputRipple Voltage
Rated Voltage	CV-5.5-12.6V	5000mA	200mVp-pMax.

3.7 Time Sequence时序特性

3.7.1Turn-OnDelayTime(TD)开机输出延迟时间:

Themaximum cold start turn-on delay shall notexceed3secondatinput230Vacand the ratedloadcondition.

在输入230Vac,额定负载情况下,最大冷启动打开的延迟不会超出3秒。

3.7.2Hold-UpTime(TH)关机输出维持时间:

2.7.2.1 Themaximum turn-off hold-up time shall beleast10mSatinput115Vacandtheratedload condition.

在输入200Vac及额定负载情况下,关机输出维持时间不低于10mS。

2.7.2.2 Themaximum turn-off hold-up time shall beleast20mSatinput230Vacandtheratedload condition.

在输入230Vac及额定负载情况下,关机输出维持时间不低于20mS。

3.7.3OutputRiseTime(TR)输出上升时间:

Input 200Vac/230Vac and ratedload, Therise time shallnotexceed50mSthattheoutputvoltagerise from10% to 90%rated voltage.

在输入200Vac/230Vac,输出额定负载条件下,输出电压由10%额定电压上升至90%额定电压的上升时间不会超过50mS。

3.8 Output Overshoot输出过冲

3.8.1 5%Rated VoltageMax. whenthepower turnon.

当电源开机时,过冲电压值最大为额定电压值的5%。

3.8.2 5%Rated VoltageMax. when thepowerturnoff.

当电源关机时,过冲电压值最大为额定电压值的5%。

OutputRated Voltage	Overshoot Voltage(V)
	Turnon	Turnoff
+12.6V	5%	5%

3.9 Output transient response输出瞬态响应

Load output voltagerange负载输出电压范围	RateSlew 斜率	Load change负载变化
12.2-12.95V	0.2A/Us	0% to 50%Load and50%to100%Load.
Vout±5%	0.2A/Us	0% to100%Load.

3.10ProtectionFunction保护功能

3.10.1OverVoltageProtection过压保护

Output voltage exceed theRated specifications120%-150%into theprotection.

输出电压超过额定规格的120%-150%时进入保护。

3.10.2OverCurrentProtection过流保护

Thepower supply shall protectitself from any over currentcondition.andshallbe

self-recovery when the fault condition isremoved. The maximumoutputcurrentshallbe100%~110%rate output current.

电源在过流情况下可自动保护,当过流情况解除后,可自动恢复正常。最大输出电流为100%~110%额定输出电流。

3.10.3 Short CircuitProtection短路保护

Shorting of output will not causepower supply todamage,oranysafetyhazard.

Thepower supply shall resumenormal operation after the shortisremoved.

输出短路时电源不会损坏,不会有任何的安全危险,短路解除后电源恢复正常工作。

3.10.4 InputProtection输入保护

Thepower supply has a currentfusetoprotectitself.

该电源由一颗电流保险丝来达到输入保护。

3.11 Average Efficiency平均效率

Inpu230Vac. and 100%,75%,50%,25%RatedLoad condition. Average

efficiency(η): 84%Min.

在输入230Vac,输出100%,75%,50%,25%额定负载,平均效率(η): 88%Min。

4ENVIRONMENTALREQUIREMENTS环境要求

4.1Temperature温度

4.1.1Storagetemperature(Non-operating)存储温度(非操作状态):

-10 to +60 degreesC[-10]至[+60]摄氏度

4.1.2OperatingtemperatureLimits操作温度:

0 to+40 degrees C[0] 至[+40]摄氏度

4.2RelativeHumidity相对湿度

4.2.1StorageHumidity(Non-operating)存储湿度(非操作状态):

10% to 80%RH(Non-condensing)[10%]至[80%],无凝水状态

4.2.2OperatingHumidityLimits操作湿度:

0% to 85%RH(Non-condensing)[0%] 至[85%],无凝水状态

4.3TheSeaLevelAltitude海拔高度

4.3.1StorageAltitude可存储海拔度(非操作状态):

0 to +20,000 feet above thesealeve[0]至[20,000]英尺

4.3.2OperatingAltitude可工作海拔度:

0 to +10,000 feet above thesealeve[0]至[10,000]英尺

4.4CoolingMethod冷却方法

Natural convection orForced air自然冷却或通风冷却

Note: Thepower storage time during which thepower hasneverbeenusedshouldbelessthan

6months, otherwise, therush current tends tomalfunction withpowerstarted.

说明: 电源存贮时间不得超过半年(在此期间,电源从未使用过),否则开机时的冲击电流可能损坏电源。

5Reliability可靠性

5.1 MTBF:Mean TimeBetweenFailure平均故障间隔时间

Thepower supply shallbe designed and manufactured tohavemore than30,000

operatinghours (about 3.5 years for 24-hour-operation a day)ofmeantimebetween

failure(MTBF) at 90% of confidence level whileoperatingunder theprevailingconditionsbelow.

在如下条件,该电源设计和制造平均故障间隔时间(MTBF)将超过30,000个操作时间(大约 操作24小时/每天/3.5年),信心指数为90%。

ACInput Voltage:200/240Vac

输入电压:200/240Vac

OutputLoad: 80% ofmaximumload

输出负载:80%最大负载条件

Ambient Temperature: at 25 degreesCRoom Temperature

环境温度:室温25摄氏度

3.12 Charging curve graph充电曲线图……

3.13 Chargingindication status充电指示状态…

红灯常亮时，表示正在充电中，绿灯常亮时表示充电完成.

3.14Charging-to-full-indicator-switchingcurrent转灯电流

充电电流在大于0.36A时，绿灯转红灯，小于0.36A +10%时，红灯转绿灯.

5.2InsulationResistance绝缘阻抗

TestPoints检测部位	Condition & Specification条件及规格
Input to Output输入-输出	DC500V10MΩmin. (at ambient temperature25 degreeC,humidity70%)DC500V10MΩ最小。 (在室温25摄氏度,湿度70%条件下)。
Input to Case输入- 外壳	DC500V10MΩmin. (at ambient temperature25 degreeC,humidity70%)DC500V10MΩ最小。 (在室温25摄氏度,湿度70%条件下)。
Output To Case输出- 外壳	NonIsolated

5.3Hi-Pot绝缘耐压

TestPoints	检测部位	Condition & Specification条件及规格
Input toOutput	输入-输出	3000Vac 50Hz,1Minute,≤10mA.
Input toCase	输入- 外壳	3000Vac 50Hz,1Minute,≤10mA.
Output ToCase	输出- 外壳	NonIsolated

When AC voltage of 3.0KVis applied, and the voltageapplied to theinsulationundertestis

gradually raised from zero to theprescribed voltagein1s,andheld at thatvalue for60sbetweentheinput and output andbetween theinput and housing,thecurrentsensitivityshallbelessthan10mA. After this test, the adapter shall exhibitno electrical andmechanicalabnormalities.（ACvoltage of 3.6KV,2s and sensitivity current10mA shallbe appliedtotheproductline).

在输入端对输出端及输入端对外壳间施加了3.0KV电压,并且测试中施加在绝缘上的电压是在1S内由0V逐渐上升到规定值,然后保持60S,电流灵敏度设置在10mA。经过以上测试,电源应 不发生电气及机械上的异常.(注: 在生产线批量生产时以3KV,2S10mA进行测试)。

5.4Leakage Current漏电流

The leakage current shallnot exceed 0.25mAforClassⅡwhenpowersupplyisoperatedmaximuminput voltage andmaximumload.

当电源供应器操作在最大输入及最大负载情况下，其漏电流应小于0.25mA,满足ClassⅡ 等级。

SAFETY STANDARD安全标准

6.1 SAFETY STANDARD安全标准

EN60335

6.2ELECTROMAGNETIC COMPATIBILITY (EMC)电磁兼容性

6.2.1EMI电磁干拢

This power supply shall compliance with the followingCriterion本电源将遵照以下标准:

6.2.1.1 ConductionEmission传导干扰度

*EN60335, ClassB *FCCPart15,ClassB

6.2.1.2 RadiatedEmission辐射干扰度

*EN60335, ClassB *FCCPart15,ClassB
6.2.2EMS电磁抗拢

This power supply shall compliance with the followingCriterion本电源将遵照以下标准:

6.2.2.1 ESD静电抗扰度

Standard: *IEC61000-4-2

AIRDISCHARGE at 8KV, CONTACTDISCHARGE at 4KV.

6.2.2.2 EFT脉冲群抗扰度

Standard: *IEC61000-4-41KV

6.2.2.3 Surge雷击浪涌

Standard: *IEC61000-4-51KV
Remarks: EMC-SPECIFICATION test with thePureresistance asloadtotest,and weonlyresponsible for theproduct we supplied.
电磁兼容性测试是以纯电阻作为负载测试的，我们只对单品测试负责。

7MECHANICAL CHARACTERISTICS机械性能

7.1BendingTest摇摆(弯曲)测试

Fixed themain and plug of the adapter,andapplyaloadof300gtotheotherends.Turnthecableconnected to eachby ±60 degrees around the connection.Carryoutthisprocess1000timesatarate of 40 timesperminute(abending of120 degrees shallbe countedasoneprocess)inX

direction. (at:25℃±5℃). AsfollowingFigure A. The cable wires shallnotbebrokenafter thistest.The electricalperformance isnormal.

以测试冶具固定Plug,吊重300g,左右摇摆±60度,每分钟摇摆40次，摇摆1000次以上(注:±60度 即120度为一个循环,算1次)(温度:25℃±5℃). 参如下图A. 测试后,线材无破裂,且电性功能正常.

7.2TensileStrengthTest拉力测试

Fixed either of theplug or the mainbody with thetesttools,thenapplya20Nloadatthe30Cm

distant from the SR for 60S. As fogireB.No short oropenandSRshallbenotloosenaftertested.将插头或充电器主体固定在测试夹具上,距离围卡30Cm处施加20N的拉力,持续60秒.如图B.

测试后,产品无短路,无开路,围卡无松脱,

7.3DropTest跌落测试

The adapter shall exhibitno abnormality inmechanical orelectricalperformancewhenitisdropped three times to hardwood(20mm thickness) from aheightof 70cm,witheachof

the three different sides of the adapter onetime.Smallnicksor slightdeformationsinthe

corners of the housing, or cracksnotpenetrating theinsidemaybeaccepted.(at:25℃±5℃).适配器经过落地测试后应无机械或电气性能异常,从70cm垂直高度自由跌落到20mm厚度

的硬木质板上(硬木质板应放置于水泥基座或同等无弹性的地面上),共跌落3次,3个不同面各 1次. 外观或角落有轻微的变形或出现不穿透裂纹是可以接受的(在25℃±5℃时)。

7.4Input and OutputConnections输入输出连接

7.4.1Input Connection输入连接:

7.4.1.1WallplugorCordtoCordType插墙式或导线式

7.4.1.2SocketandTermainalType母座或端子式

7.4.2OutputConnector输出连接:

7.4.2.1OutputPlug输出插头

OD*ID*L:

7.4.2.2Polarity极性

Seeappearancefigure详见外观图.

7.4.3Input&OutputCord输入输出线材:

7.4.3.1LengthandCord长度及颜色

Seeappearancefigure详见外观图.

7.4.3.2 Specifition规格

Seeappearancefigure详见外观图.

7.5Unit Weigth产品单重

The weight of theunitpower supply shallbe about150 g(Ref).

产品单重大约:150克(供参考).

7.6Dimension物理尺寸

112.5mm * 53mm*31.5mm(L* W*H).